+91 8866188126 [email protected]

Blog / Components

MSL and ESD: 5 Component Handling Myths That Damage Boards

Moisture and static damage parts long before reflow, usually without a visible mark. Five common handling myths, the facts behind them and simple habits for small teams.

Microplacer team · 15 November 2026 · 5 min read

Illustration: MSL and ESD: 5 Component Handling Myths That Damage BoardsComponents

When a freshly built board misbehaves, the usual suspects are the schematic or the solder joints. Sometimes, though, the fault was locked in weeks earlier, on a shelf or a bench, when a bag of chips was left open or a microcontroller travelled in an ordinary zip bag. Here are five handling myths that sound reasonable and quietly cost good boards.

Myth 1: if the part looks fine, it is fine

Both moisture and static work out of sight. A plastic IC that has quietly taken on water looks no different from a dry one. Then, in the reflow oven, that water flashes to steam inside the package and can split internal layers or tear a bond wire. Occasionally the body bulges or cracks where you can see it; usually the damage needs X-ray or acoustic imaging to find, or it shows up later as a fault that comes and goes.

Static is sneakier still. The zap you feel on a doorknob is already thousands of volts, and a sensitive chip can be harmed by a small fraction of that. The part may die at once, or limp along with extra leakage and fail months later in the field. Looking at it will not tell you which.

Myth 2: opened reels can sit on the shelf indefinitely

Plastic packages are rated with a moisture sensitivity level (MSL) under J-STD-020; J-STD-033 covers storage and use. The rating sets a floor life — your budget of open-air hours before reflow, after which the parts need drying first.

MSLTypical floor life once openedBench reality
1UnlimitedMost passives; no special storage needed for normal reflow.
2aAbout 4 weeksFine for a project, but note the opening date.
3About 1 week (168 h)Common on everyday ICs. A long weekend with the bag open eats much of it.
4 / 5 / 5aAbout 3 days / 2 days / 1 dayOpen only when you are ready to build.

Two details catch people out. First, bench time is a running total: an hour today plus an hour tomorrow is two hours, unless the parts spent the gap in proper dry storage as J-STD-033 describes. Second, the caution label on your bag beats any generic table, this one included — ratings vary by package and can be stricter for hotter lead-free reflow.

Myth 3: ESD only matters in dry winters

Dry air lets charge build up more easily, so static is more noticeable in dry months and air-conditioned rooms. But walking across a floor, peeling tape off a reel or sliding a board out of a plastic tray creates charge in any season, at levels you will never feel. If it is made of silicon, handle it as ESD sensitive all year; many datasheets list an HBM or CDM rating if you want to know how fragile a part is. And the humid monsoon months bring their own risk: that is when opened moisture-sensitive parts soak up water fastest.

Myth 4: any plastic bag is an anti-static bag

Bags look alike, but they do very different jobs.

  • Metallised static-shielding bag (the silvery, slightly see-through kind) — its metal layer steers a discharge around whatever is inside. Use it for chips, modules and finished boards.
  • Moisture barrier bag (dry pack) — the opaque foil bag parts arrive in. Its job is keeping humidity out; many types also give static shielding.
  • Pink “antistatic” bag — made so the plastic itself does not build up charge, but a spark from outside can still reach the contents. Fine as an inner wrap, not as the only protection.
  • Ordinary zip bag, bubble wrap or packing foam — no protection at all, and rubbing them creates charge. Never let them touch exposed semiconductors.

A zip lock or a strip of tape on an opened dry pack does not stop the floor-life clock either.

Myth 5: baking fixes every moisture problem

Baking does drive moisture out of a package before reflow, and J-STD-033 lists the conditions. But it is not a free reset button:

  • It cannot repair damage that already happened. A package that cracked or delaminated during an earlier reflow stays damaged.
  • The quick, hot bake warps most plastic tape, reels and tubes, so parts must first move into heat-proof trays — more handling and a chance of bent leads.
  • The gentle, low-temperature option keeps the packaging intact but can tie the parts up for days or even weeks.
  • Every bake ages the solderable surfaces on the leads a little, so baking the same parts again and again can leave you with poor joints.

Simple handling habits for small teams

You do not need a full factory ESD programme to protect a hobby or start-up bench. These habits cover most of the risk:

  1. 1Leave dry packs sealed until build day. When you do open one, snip just below the seal so the bag can be closed again, and write the opening time on it.
  2. 2Glance at the humidity indicator card first thing. If its spots have changed colour past the limit printed on the label, treat the parts as wet.
  3. 3Put leftovers back into a moisture barrier bag with new desiccant and an indicator card, seal it properly, and log the bench hours already used.
  4. 4Use a grounded wrist strap and a dissipative mat when handling ICs and boards, and keep ordinary plastics off the bench.
  5. 5Bare PCBs absorb moisture too: leave them in their sealed pack until assembly and do not let them sit for months, especially with an OSP finish, which ages fastest.
  6. 6If you send parts for assembly, keep them on reels, continuous cut tape, capped tubes or covered trays, label each with the part number and designators, and include a few spares.

For floor-life and baking tables and a checklist for shipping consigned parts, read our moisture-sensitive parts, ESD and component handling guide. You can also search parts by part number and upload your BOM through electronic components, and check the assembly quote FAQ for how supplied parts fit into a PCBA order.

#msl#esd#component-handling#j-std-033#moisture-sensitive-parts

Get an instant PCB quote

More articles

Have a project in mind?

Send us your files or get an instant online price — our engineers check every order before production.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us