+91 8866188126 [email protected]

PCB cost guide

What affects your PCB price — and how to save

Every option you pick in the online calculator changes the price a little or a lot. This guide shows which choices matter most for bare PCBs and assembly, which ones are standard, and simple ways to keep your boards affordable without hurting quality.

Get an instant quote

What the online price includes

Before comparing options, it helps to know what is already covered in the price you see.

GST

GST is part of what you pay online and is shown as its own line, so you always see the tax clearly.

Shipping in India

Delivery to your address in India is included. Bare PCBs typically reach you in 10–15 working days, express shipping included.

100% electrical test

Every board is tested with a flying probe for opens and shorts. This is always included and free — there is nothing to add.

Engineering file check

Our engineers check your files before production starts, so problems are caught before money is spent on boards.

Minimum 5 PCBs

The smallest order is 5 boards. The next quantity step often costs only a little more in total — compare both in the calculator.

Pay when you order

You pay at order time by online payment or bank transfer. Production starts after payment and the file check.

Size, layer count and quantity

These three choices set most of the bare PCB price. Everything else adjusts it.

ChoiceHow it affects the priceTip
Board sizeMore area means more laminate, copper and processing. Larger boards usually cost more per piece, and very large boards may also cost more to ship.Keep the outline as compact as your enclosure allows. Size is read from your Gerber outline.
Layer count1 and 2 layers are the most economical. Each step up (4, 6, 8 … up to 16 online) adds lamination and drilling steps, so the price rises noticeably.Use 4 layers only when you need inner ground/power planes or the routing is dense. Boards above 16 layers are priced by our team.
QuantityQuantities come in fixed steps (5, 10, 15 … then larger steps). The order total goes up with quantity, but the price per board usually falls.Look at the price per board, not only the total. Ordering a few spares now can be cheaper than a second small order later.
Delivery formatSingle PCBs, a panel made by Microplacer, or your own panel file. With a panel, the quantity is the number of panels.Assembly always needs a panel. See the panel guide.

Price per board vs order total

A small order carries fixed work (file check, setup, testing) that is shared by very few boards, so each board looks expensive. As the quantity grows, that fixed part is spread over more boards and the price per board drops — even though you pay more in total.

Material, TG, thickness and copper weight

Standard choices give the lowest price and the most options. Special choices cost more, and some are sent to our team for a quote.

OptionStandard (lowest cost)Costs moreSent for a quote
Base materialFR-4 (glass-epoxy)Flex (polyimide), 1–2 layers, ENIG finishAluminium, copper core, Rogers, PTFE
Material type / TGFR-4 TG135Higher TG (TG140, TG155, TG170) and named laminate brands. From 8 layers the calculator offers only higher-TG material.—
Board thickness1.6 mmSome thinner or thicker values; the available list depends on the layer count—
Outer copper1 oz (35 µm)2 oz on all layer counts; heavier copper (up to 4.5 oz) on 2-layer boards—
Inner copper (4+ layers)0.5 oz1 oz or 2 oz (heavier copper usually costs more)—
Product typeIndustrial / consumer—Aerospace and medical (stricter inspection and documentation)

The calculator only shows the thicknesses, copper weights and materials available for the layer count you choose. Full limits are on PCB capabilities and flex PCB capabilities.

Surface finish and mask colour

FinishTypical costGood for
HASL (with lead)LowestGeneral boards with normal-size parts where RoHS compliance is not required.
Lead-free HASLLowRoHS products with normal-size parts.
OSPLowFlat pads at low cost; best when boards are assembled soon, as the coating has a short shelf life.
ENIGHigherFlat gold pads for fine-pitch and BGA parts and longer storage. A thicker gold option (2 U") costs more again.

Green is the standard colour

Green solder mask is the standard and the fastest choice. Red, yellow, blue, white, black and purple are also offered — they look different but work the same electrically. Silkscreen is white on all colours and black on a white board.

Not every finish fits every board

Some finishes are not offered on every layer count, and very small vias are not possible with HASL. If an option is missing in the calculator, it is not available for that board.

Advanced options that add cost

These options solve real design needs, but each adds process steps. Choose them only when your design requires them.

OptionWhy you might need itNotes
Via plugging / fillingSealed vias; filled-and-capped vias are the usual choice for via-in-pad under BGA parts.Tented vias (covered by mask) are standard. Plugged, epoxy-filled and copper-paste-filled options add process steps and cost; filled-and-capped is typically the most expensive.
Smaller minimum viaVery dense routing, fine-pitch BGA breakout.4+ layers only. The smallest sizes need a more precise process and sometimes higher-TG material and the Kelvin test.
Castellated holesPlated half-holes so your board can be soldered onto another board as a module.Available from 2 layers.
Gold fingersHard-gold edge contacts that plug into a slot.Bevelled edges are available for easier insertion.
Impedance controlUSB, HDMI, Ethernet and RF lines that need a defined stack-up.4+ layers. An impedance test report is an extra option.
Tight outline toleranceClose-fitting enclosures or edge connectors.±0.2 mm is standard; ±0.1 mm precision costs more.
Edge platingShielding or grounding along the board edge.—
Backdrilling / press-fit holesThick high-speed boards; solderless press-fit connectors.4+ layers only.
4-wire Kelvin testResistance test of every via, required for small vias on multilayer boards.The standard flying-probe test is already free.
Reports and packagingInspection or impedance reports, humidity indicator card, paper between boards.Each is an optional extra. Production-file approval before manufacturing adds about a day.
Panel extrasNot accepting crossed-out (X-out) boards in a panel, high-precision silkscreen.Accepting X-out boards and ink-jet silkscreen are the standard, cheaper choices.

Assembly cost drivers

The assembly price is separate from the bare PCB price and is shown next to it in the calculator.

Solder pads per board

SMD pads on the side(s) we assemble plus through-hole pads. More pads means more placement and soldering work.

Number of boards

Assembly is priced in steps of 5 boards, and the price per board falls as the quantity rises.

Stencil

For 5–50 boards the stencil is free. From 55 boards a one-time shared stencil charge is added.

One side or both

With both sides assembled, the SMD pads on both sides are counted. Placing SMD parts on one side where practical also avoids a second print-and-reflow pass.

Components

Not part of the assembly price. Parts we source are quoted separately from your BOM. You can also send your own parts — we confirm what to send after checking the BOM.

Engineering review

BGA/LGA parts or 0201 and smaller parts are reviewed by our engineers before a price is given.

Assembly is done in panels only. For the full pricing rules, see the PCB assembly quote FAQ.

When a price can change after the engineering check

Most orders go through at the price you paid. Occasionally the file check finds something the calculator could not see.

  1. 1

    You order and pay the online price

    The price is based on the options you chose and what we could read from your Gerber.
  2. 2

    Our engineers check your files

    For example, the real board size, layer count or smallest via may differ from what was entered, or a feature needs a costlier process.
  3. 3

    If the price changes, you decide

    We tell you the new price and why. You can accept it and pay the difference, or cancel the order and get a refund.

    Tip: Entering the correct size, layers and options up front avoids most price changes.

Design-for-cost checklist

Small decisions at the design stage often save more than any option in the calculator.

Start with standard options

FR-4 TG135, 1.6 mm, 1 oz copper, green mask, HASL or lead-free HASL, tented vias. Change only what your design truly needs.

Choose a sensible board size

Avoid empty board area. A compact outline lowers material cost and suits panels better.

Use as few layers as practical

If a clean 2-layer layout works, it will cost less than 4. Move up only for planes, density or signal needs.

Keep hole sizes consistent

Fewer different drill sizes and normal via sizes keep drilling simpler. Very small vias need a more precise process.

Skip unneeded advanced features

Gold fingers, filled vias, tight tolerances and extra reports all add cost. Use them where they solve a real problem.

Pick ENIG only when needed

Fine-pitch or BGA parts benefit from ENIG. For normal parts, HASL or lead-free HASL is usually enough.

Plan assembly early

Place SMD parts on one side where possible, mark polarity clearly and keep BOM, pick-and-place file and silkscreen in sync.

Compare quantity steps

Check the price per board at the next quantity step — a few extra boards can cost very little.

Frequently asked questions

Much of the work on a small order is fixed — file check, setup and testing. That cost is shared by all the boards, so adding boards often raises the total only slightly while the price per board falls.

Green is the standard and the fastest colour. Other colours work the same electrically; check the calculator to see the price and timing for the colour you want.

No. Every board is 100% tested with a flying probe for opens and shorts, free of charge. The 4-wire Kelvin test is a separate option needed only for small vias on multilayer boards.

Special materials (aluminium, copper core, Rogers, PTFE), 18+ layers, aerospace or medical grade, and assemblies with BGA/LGA or 0201 parts are priced by our team. Send your files and we email you the quotation.

No. The assembly price covers the assembly work (and the stencil when charged). Parts we source are quoted separately from your BOM. See the assembly quote FAQ.

If the engineering check finds the order needs a different price, we explain why. You can accept and pay the difference, or cancel and get a refund.

Related questions

Learn more — answers to the questions people ask next.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us