+91 8866188126 [email protected]

EMS guide · Quality

Quality certifications & standards explained

ISO, IPC, RoHS, UL, BIS… Electronics manufacturing comes with many logos and codes. This page explains what each one really means, which ones matter for your product, and how to write them into your order so everyone builds to the same rules.

Get an instant quote

See how it works

Your productWritten requirementsQuality systemWorkmanshipMaterials & complianceInspection & records
1/5 · Why standards matter

Standards give you and your supplier one shared, written meaning of “good quality”.

Quality certifications and standards explained: Why standards matter — Standards give you and your supplier one shared, written meaning of “good quality”. Quality systems — ISO-type certificates cover how a company is run — choose the one that fits your industry. Workmanship standards — IPC standards describe what an acceptable board, solder joint or cable looks like. Inspection — Inspection checks boards against the agreed standard and class — not against opinion. Compliance & reports — Ask for current certificate copies, their scope and compliance declarations such as RoHS.

What this page is about — and who it is for

Certificates and standards are a common language between you and the factory that builds your boards. Used well, they remove guesswork; used only as logos, they mean very little.

Product and hardware startups

Learn which standards are worth asking for at the prototype stage and which ones only matter when you move to production.

Purchase and sourcing teams

Understand what a certificate covers (and what it does not) so you can compare suppliers fairly and write clear purchase orders.

Engineers in regulated fields

Medical, automotive, aerospace, defence and industrial products often have their own quality rules. Know which ones your customer or regulator expects.

Certificate vs standard — the simple difference

A standard is a document that describes how something should be done or how a good result looks (for example, an acceptable solder joint). A certificate is proof from an independent body that a company has been audited against a standard — for a defined scope (site, products and activities). Always read the scope, not just the logo.

Quality management systems

These certify how a company is organised: document control, training, supplier control, handling of problems and continual improvement. They do not, on their own, describe how a solder joint must look.

StandardWhat it coversWhen to ask for it
ISO 9001The general quality management system: processes, records, customer focus, corrective action and improvement.A sensible baseline for any electronics supplier.
ISO 13485Quality management for medical devices, with more focus on risk management, traceability and documented controls.When your product is (or is part of) a medical device.
IATF 16949Automotive quality management, built on ISO 9001 with extra automotive requirements such as defect prevention and supply-chain control.When you supply into the automotive chain and your customer requires it.
AS9100Aerospace and defence quality management — ISO 9001 plus extra requirements for safety, configuration and product traceability.For aerospace, space and defence programmes that call for it.
ANSI/ESD S20.20An ESD (electrostatic discharge) control programme: grounding, protected areas, packaging and training.When your boards carry static-sensitive parts — which is most modern electronics.

Workmanship standards (IPC)

IPC standards describe what “acceptable” looks like for bare boards, assemblies and cables. Most of them define three product classes — you choose the class, and inspection follows it.

StandardUsed forIn simple words
IPC-A-600Bare printed boardsVisual acceptance of the bare PCB: copper, plating, solder mask, holes, edges and markings.
IPC-A-610Assembled boards (PCBA)What an acceptable assembly looks like: solder joints, part placement, polarity, cleanliness and damage.
IPC J-STD-001Soldering processRequirements for materials and methods used to make soldered connections — the “how to solder” companion to IPC-A-610.
IPC/WHMA-A-620Cables and wire harnessesAcceptance of crimps, wire preparation, splices, connectors, labels and harness build.

Class 1 — general electronics

Products where the main need is that the assembly works. Cosmetic imperfections are generally allowed.

Class 2 — dedicated service

Products expected to work for a long time without interruption, though not critical. A common choice for industrial and commercial electronics.

Class 3 — high reliability

Products where downtime is not acceptable or that work in harsh environments. Tighter limits mean more inspection and usually higher cost.

Material and product compliance

These are about what goes into your product and whether the finished product may be sold in a market.

RoHS

An EU rule that restricts certain hazardous substances (such as lead in solder) in electrical and electronic equipment; similar rules exist in other markets, including the E-waste rules in India. Decide early whether your build must be RoHS compliant — it affects the solder, the PCB finish and the parts.

REACH

A European regulation on chemical substances. Buyers usually ask for a declaration covering substances of very high concern in parts and materials.

UL 796 and UL marking

UL 796 is the UL safety standard for printed boards (for example flammability and bonding of the copper to the base material). A UL recognition is limited to the specific materials and constructions that were approved — check that your board falls inside that scope.

BIS (India)

Some finished electronic products sold in India must be registered under the BIS Compulsory Registration Scheme before sale. This applies to the product owner and the product category, not to every bare board.

Other market approvals

Radio products, safety-critical equipment and exports may need further approvals (for example WPC approval for wireless products in India, or the rules of your export market). Check the rules for your product and target market.

Declarations from suppliers

Compliance is proven with documents: material declarations, test reports and certificates of conformity from the component and material makers.

How to use standards when you choose a supplier

A short, practical process that works for prototypes and production.

  1. 1

    Decide what your product really needs

    Look at your market, your customer contract and any regulator. A consumer gadget, a medical monitor and a car module have very different needs.

    Tip: Do not ask for Class 3 or industry certificates “just in case” — it adds cost without adding value if your product does not need it.

  2. 2

    Write the requirement into your order

    State the IPC class, the standard edition if your customer specifies one, RoHS or leaded build, and any special inspection or reports. Put it in your fabrication notes, assembly notes or purchase order. See preparing your files.
  3. 3

    Ask for current certificate copies and check the scope

    Check the certificate holder name, the site address, the activities covered and the expiry date. A certificate for one site or activity does not automatically cover another.
  4. 4

    Agree how quality will be shown

    Agree what you will receive with the delivery — for example electrical test results, inspection records, a certificate of conformity or first-article checks — before production starts.
  5. 5

    Review the first delivery against the standard

    Inspect the first boards using the same standard and class you specified. If something does not match, raise it early so corrective action happens before the next batch.

What to send us when quality requirements matter

ItemWhy it helpsNeeded?
Gerber / BOM / pick-and-place filesThe basis for any PCB or assembly quote.Yes
Required IPC class and standardsSets the inspection limits and the build method.If you have a requirement
RoHS or leaded buildDecides solder, surface finish and part selection.Yes, for assembly
Industry or customer requirementsMedical, automotive, aerospace or customer-specific quality rules.If applicable
Documents you need with deliveryFor example test results, certificate of conformity or material declarations.If applicable

Standard boards — order online

If your boards have no special quality requirements, FR-4 and flex PCBs up to 16 layers get an instant online price (GST and shipping included), and our engineers check your files before production.

Special quality requirements — talk to us first

If your product needs a specific class, industry standard or document set, tell us your requirement. We review it and confirm what we can provide before you order.

Quality and checks at Microplacer

Here is what every order gets. For our own certificates and quality approach, see our quality standards page.

Engineering file check

Our engineers check your files before production and contact you if something needs your decision.

100% electrical test

Every bare PCB is electrically tested with a flying-probe tester for opens and shorts. More in testing & inspection.

Assembly review where it matters

Boards with BGA, LGA or 0201 parts go through engineering review before pricing, because their joints need special care and inspection.

Our certificates

See our quality standards, and ask us for current certificate copies when you need them for your supplier file.

Frequently asked questions

No. ISO 9001 shows that the company runs a managed quality system. The quality of each board is defined by the workmanship standard and class you specify (for example IPC-A-610 Class 2) and checked by inspection and testing.

Most commercial and industrial products use Class 2. Choose Class 3 only when your product must work without failure or in harsh conditions, or when your customer requires it — it means tighter limits and usually higher cost. Class 1 suits simple products where function is all that matters.

J-STD-001 covers the materials and process for making soldered connections. IPC-A-610 is the visual acceptance standard for the finished assembly. They are often used together.

It depends on where the product will be sold. If the final product must be RoHS compliant, build your prototypes the same way so you test the real solder, finish and parts.

No. A UL recognition for printed boards covers specific materials and constructions. Approval of your finished product is a separate process for the product owner.

Only certain product categories notified under the Compulsory Registration Scheme need it before sale in India. Check the current list for your product; the registration is held by the product owner or brand.

Please see our quality standards page and ask us for current certificate copies. Check the scope on any certificate you receive.

Related questions

Learn more — answers to the questions people ask next.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us