+91 8866188126 [email protected]

Multilayer PCB guide

Multilayer stack-up and controlled impedance basics

Going from 2 layers to 4, 6 or more changes how your board is built and how fast signals behave on it. This guide explains what a stack-up is, how to pick a layer count, when you need controlled impedance and how to ask for it when you order online.

Get an instant quote

What a stack-up is

A stack-up is the recipe of a multilayer board: which copper layers sit where, and what insulating material separates them.

Core

A rigid sheet of cured glass-epoxy laminate with copper foil already bonded on both sides. Inner layer patterns are etched on cores.

Prepreg

Glass cloth soaked in resin that is not yet fully cured. It sits between cores (and between a core and the outer foil) and acts as the glue.

Copper foil

The outer layers usually start as plain copper foil pressed on top of prepreg. They are plated and etched later, together with the holes.

During lamination the whole sandwich is heated under pressure: the prepreg resin flows, fills the gaps between inner traces and cures, so cores and foils become one solid board. The thickness of each core and prepreg sets the distance between copper layers — and that distance is what decides impedance. For the full production flow (inner layer imaging, lamination, drilling, plating and so on) see how PCBs are made.

LayerTypical role in a 4-layer boardMade from
L1 — topComponents and signal tracesCopper foil + plating
L2 — innerSolid ground plane (reference for L1)Core copper
L3 — innerPower plane(s) or ground / slow signalsCore copper
L4 — bottomSignals and componentsCopper foil + plating

Choosing a layer count

There is no single right answer, but these rules of thumb help most designs. Choose the same layer count as your Gerber files.

LayersUsually a good fit forThings to keep in mind
2Simple and low-speed boards, power supplies, hobby and basic microcontroller designsNo inner plane, so return paths and noise depend on careful routing and a good ground pour. Controlled impedance is not offered on 2 layers in our calculator.
4Most microcontroller boards with USB, Ethernet, Wi-Fi/BLE modules, mixed analog and digitalA solid ground plane right under the top layer makes signals quieter and impedance predictable. Often the best cost-to-performance step up from 2 layers.
6Dense boards, fine-pitch parts, several power rails, DDR memoryRoom for two ground planes so every signal layer can sit next to a reference plane.
8 and moreProcessors with large BGAs, many high-speed interfaces, tight EMC targetsMore planes and routing layers; our calculator offers higher-TG laminate for these layer counts (see below).

Keep planes solid

A ground plane works best as one unbroken sheet of copper. Every slot or cut-out forces return current to take a detour.

Pair signals with ground

A common rule of thumb: every signal layer should sit directly next to a ground (or at least a plane) layer, not between two other signal layers.

Keep it symmetrical

Mirror the copper and dielectric arrangement around the middle of the board. Symmetric stack-ups bow and twist less after lamination and reflow.

Layer counts you can order online

Our calculator gives an instant price for rigid FR-4 boards with 1, 2, 4, 6, 8, 10, 12, 14 and 16 layers. Boards above 16 layers, or materials such as Rogers, PTFE, aluminium and copper core, can be sent to us for a quote.

Copper weight and board thickness options

Copper weight is given in ounces per square foot: 1 oz is about 35 µm thick. These are the choices our online calculator offers for rigid FR-4 boards, by layer count.

LayersBoard thickness (mm)Outer copper (oz)Inner copper (oz)
10.8, 1.0, 1.2, 1.6, 2.01, 2—
20.4 (ENIG only), 0.6, 0.8, 1.0, 1.2, 1.6, 2.01, 2, 2.5, 3.5, 4.5—
40.8, 1.0, 1.2, 1.6, 2.01, 20.5, 1, 2
60.8, 1.0, 1.2, 1.6, 2.01, 20.5, 1, 2
80.8, 1.0, 1.2, 1.6, 2.01, 20.5, 1, 2
101.0, 1.2, 1.6, 2.01, 20.5, 1, 2
121.2, 1.6, 2.0, 2.51, 20.5, 1, 2
14 and 161.6, 2.0, 2.51, 20.5, 1, 2

1.6 mm is the usual standard thickness. Heavier copper carries more current and spreads heat, but it also needs wider gaps between traces and changes the impedance of a trace — so decide copper weight before you calculate trace widths. See all limits on the PCB capabilities page.

Controlled impedance: when do you need it?

Once a trace is long compared with the rise time of the signal, it behaves like a transmission line. If its impedance does not match the driver and receiver, part of the signal reflects back and the edges ring. Controlled impedance means the board is built so that chosen traces hit a target value.

InterfaceCommonly used target (check your chip datasheet)Line type
USB 2.0 / USB 3.x90 ΩDifferential pair
HDMI100 ΩDifferential pairs
Ethernet (between PHY and magnetics)100 ΩDifferential pairs
DDR memoryOften 40–50 Ω single-ended, 80–100 Ω for clock/strobe pairsBoth
RF lines (antenna, GNSS, Wi-Fi feed)50 ΩSingle-ended (microstrip or coplanar)
MIPI, LVDS, PCIe and similarTypically 85–100 ΩDifferential pairs

Because laminate thickness, resin content, copper thickness and etching all vary slightly, impedance is always specified with a tolerance. A common industry tolerance is around ±10% of the target; tighter tolerances are harder to build and must be discussed in advance. Always take the target values from the datasheet or design guide of the chip you are using — the numbers above are only common examples.

Requesting controlled impedance in our calculator

Controlled impedance is available on rigid boards with 4 or more layers.

  1. 1

    Choose 4 or more layers

    Set Layers to the copper layer count of your design (4–16 online). The impedance option is not shown for 1–2 layer boards or flexible boards.
  2. 2

    Tick “Specify stack-up (impedance)”

    This tells us your design needs controlled impedance, so your board is built to a defined stack-up instead of the factory’s default build.

    Tip: Pick inner and outer copper weight and board thickness first — they are part of the stack-up.

  3. 3

    Add the impedance test report if you need proof

    Once a stack-up is specified you can also choose Impedance test report — a report of the measured impedance values for your boards. Useful for production batches and for customers who must keep records.
  4. 4

    Send your impedance details with the files

    Put the target values, the layers they are on and the trace width/spacing in a readme or drawing inside your Gerber zip, or summarise them in the Note for us field of the order form. See the list of design inputs below.
  5. 5

    Our engineers confirm the stack-up

    Before production our engineers check your files and the impedance request against the materials and stack-ups that can actually be built. If the trace widths need a small adjustment to hit your target, or something is unclear, we contact you before production goes ahead.

    Tip: If the final price changes after this check, you can accept and pay the difference, or cancel and get a full refund.

Why the stack-up is confirmed by an engineer

Impedance depends on the real dielectric thickness and material after lamination, not only on your CAD settings. A design calculated with a dielectric value that cannot be built will miss its target. Letting our engineers confirm the stack-up — ideally before you finish routing — avoids boards that look right but do not perform.

Single-ended vs differential lines, and what to send us

Single-ended

One trace referenced to a nearby plane, for example a 50 Ω RF feed or a DDR data line. Its impedance depends mostly on trace width, copper thickness and the height of the dielectric to the reference plane.

Differential pair

Two traces carrying opposite signals, for example USB, HDMI or Ethernet. Besides width and dielectric height, the gap between the two traces sets the differential impedance. Keep both traces the same length and route them together.
Design inputWhat to tell us
Target impedance and toleranceFor example “90 Ω differential ±10%” or “50 Ω single-ended ±10%”.
Layer of the traceWhich copper layer the controlled traces are on (e.g. L1, L3).
Trace width and spacingWidth of each trace and, for pairs, the gap between them — as drawn in your Gerber.
Reference plane(s)Which layer(s) act as ground reference for that trace — one plane for outer layers, often two for inner layers.
Coplanar ground (if used)The gap from the trace to the surrounding ground pour, for coplanar waveguide RF lines.
Your assumed stack-upDielectric heights and copper weights you used in your impedance calculator, so we can compare.

Tip: mark controlled-impedance nets clearly (a separate net class or a note on the fab drawing). How to package all of this is explained in Preparing your design files.

High-speed layout tips

Controlled impedance only helps if the rest of the layout supports it. These general practices apply to most fast designs.

Continuous return path

Every fast signal needs an unbroken reference plane directly under it. The return current flows right below the trace — give it a clear road.

Never cross a plane split

Routing a high-speed trace over a gap between two planes breaks its return path and causes noise and emissions. Re-route or add stitching capacitors.

Stitch layer changes

When a signal moves to another layer through a via, place a ground via close by so the return current can change layers too.

Match lengths

Keep the two traces of a differential pair the same length, and match lengths within buses such as DDR as the chip vendor recommends.

Keep stubs short

The unused part of a through-hole via below the layer where the signal leaves it is a stub. At high data rates a stub causes reflections and can resonate. On thick multilayer boards the Backdrill option (4+ layers) drills out that leftover via barrel.

Space pairs apart

A common rule of thumb (the “3W rule”) is to keep other traces at least about three trace widths away, centre to centre, from a fast signal or pair to reduce crosstalk.

Higher-TG laminate for higher layer counts

TG (glass-transition temperature) is the point where the laminate starts to soften. Multilayer boards contain more resin layers and plated holes, and lead-free reflow runs at high temperature, so they benefit from higher-TG material that expands less through the board thickness.

LayersTG options in our calculator
1TG135
2 and 4TG135, TG140, TG155
6TG135, TG155, TG170
8TG155, TG170
10 to 16TG170

The calculator only shows the material types offered for the layer count you pick. Different laminates also have slightly different dielectric constants, which affects impedance — one more reason we confirm the stack-up for controlled-impedance orders. For RF designs that need Rogers or PTFE material, send your files for a quote. More on materials and limits on the PCB capabilities page.

Frequently asked questions

Not through our online calculator — the “Specify stack-up (impedance)” option appears for 4 or more layers. On a 2-layer 1.6 mm board the reference plane is far away, so 50 Ω or 90 Ω lines would need very wide traces anyway. If you have a special case, send your files for a quote.

It helps a lot. Send the target impedances, the layers, trace widths and spacing, and the dielectric heights you assumed. Our engineers check it against what can be built and contact you if anything needs adjusting.

“Specify stack-up (impedance)” means your board is built to a defined stack-up for your impedance targets. The impedance test report is an optional extra document with the measured values, available once the stack-up option is selected.

For inner signal layers, thinner copper (0.5 oz) lets you etch finer traces more accurately. For inner power or ground planes carrying high current, 1 oz or 2 oz is common. Decide before calculating trace widths, because copper thickness changes impedance.

Yes. Every board, including multilayer boards, gets a 100% flying-probe electrical test for opens and shorts at no extra cost.

The minimum is 5 PCBs. The online price includes GST and shipping within India. See the online ordering FAQ for payment and delivery details.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us