+91 8866188126 [email protected]

PCB assembly guide

BOM best practice: approved alternates, lifecycle and obsolescence

Your bill of materials (BOM) is the shopping list for every board we assemble. A clear BOM with exact part numbers, sensible alternates and parts that are still in production gets an accurate component price quickly and avoids the most common assembly surprises: wrong parts, long waits and redesigns late in the project.

Get an instant quote

Why the BOM decides component cost, lead time and the risk of wrong parts

On many assembled boards the components cost more than the bare PCB and the assembly labour together. Every line of the BOM is a buying decision, so small gaps in the BOM turn into real cost, delay or risk.

Cost

A part described only as "10k resistor" can be bought in dozens of grades. An exact manufacturer part number (MPN) lets us price the part you actually designed for, not a guess that may be too cheap or too expensive.

Lead time

One hard-to-find part can hold up an entire build. Lines with no alternates, or parts near the end of their life, are typically the ones that decide when the kit of parts is complete.

Risk of wrong parts

Mismatches between the BOM, the schematic and the footprint on the PCB (wrong package, wrong value, wrong pin-out) are among the most common causes of assembly rework. A clean BOM catches them before parts are bought.

The short version

Give every placed part an exact manufacturer part number, mark parts that are not fitted, list alternates you are happy with, and check that nothing on the BOM is already end-of-life. That alone removes most sourcing questions.

Beyond the basic columns: part numbers, package and value checks

The minimum BOM columns (reference designators, quantity, manufacturer and MPN, description) are listed in our design files guide. This section covers the extra checks that make a BOM easy to source and hard to get wrong.

Column or checkWhy it mattersGood practice
Manufacturer part number (MPN)Identifies one exact part: value, tolerance, package, temperature range and packaging.Use the full orderable MPN including suffixes. Suffixes often change packaging, grade or RoHS status.
Package / footprintThe part must fit the land pattern on the PCB.Add a package column (for example 0603, SOT-23-5, QFN-32 5x5 mm) and check it matches the footprint in your layout. Footprints based on IPC-7351 naming make this easier to review.
Value and tolerancePassives with the same value can differ in tolerance, voltage, dielectric or power rating.For capacitors state value, voltage and dielectric (for example 10 uF, 16 V, X7R). For resistors state value, tolerance and power.
Reference designatorsTell us where each part goes.The count of designators on a line must equal the quantity per board. Designators must match the silkscreen and pick-and-place file.
Polarity and orientation notesDiodes, LEDs, electrolytics and ICs can be placed the wrong way round.Make sure pin 1 and polarity marks are on the silkscreen and in the assembly drawing; add a note for any unusual part.
Customer-supplied or special partsSome parts you may want to supply yourself or have programmed.Mark these clearly in a notes column so they are not bought twice.
  1. 1

    Export the BOM from the same design revision as the Gerbers

    A BOM from an older revision is a frequent source of wrong or missing parts. Export BOM, pick-and-place and Gerbers together.
  2. 2

    Check each MPN against its datasheet package

    Open the datasheet for each line and confirm the package and pin-out match the footprint used in the layout, especially for ICs that come in several packages.
  3. 3

    Cross-check quantities

    Quantity per board should equal the number of reference designators on that line. A mismatch usually means a missing or duplicated designator.
  4. 4

    Remove ambiguity

    Replace generic descriptions ("LED red", "header 2.54") with exact part numbers. If any part on the line is acceptable, say so and give the key parameters.

    Tip: One line per unique MPN keeps the BOM short and easy to compare with quotes.

Do-not-place (DNP) lines, variants and parts that are not on the BOM

Many designs have footprints that are left empty on purpose: optional features, tuning parts, debug headers or parts for a different product variant. If this is not clear in the files, those parts may be bought and placed by mistake, or missed when you actually need them.

Marking DNP parts

Keep DNP parts on the BOM with a clear "DNP" or "Do not place" mark and quantity 0, or remove them from both the BOM and the pick-and-place file. Do not leave them in one file and not the other.

Product variants

If one PCB is built in several variants, send a separate BOM for each variant you want built, named clearly (for example Variant-A, Variant-B), rather than one BOM with notes.

Parts placed by hand or later

Connectors, batteries, displays or heavy parts that you will fit yourself should be marked as not assembled, so they are not included in the component price.

Parts not on the BOM

Mechanical items such as screws, standoffs, heatsinks, labels or cables are often missing from an electronic BOM. If you want them supplied or fitted, list them on separate lines.

Check DNP against pick-and-place

A common rule: every designator in the pick-and-place file should either have a BOM line or be marked DNP. Designators that appear in only one file are a warning sign and will usually lead to a question from our engineers.

Approved alternates and the risk of single-source parts

A single-source part is one that only one manufacturer makes, in one exact form. If it goes out of stock, the build waits. Approved alternates give a second or third option that you have already accepted as electrically and mechanically equivalent.

Type of partHow easy to find an alternateWhat to check before approving one
Chip resistorsUsually easy: many makers produce equivalent parts in standard sizes.Value, tolerance, power rating, size; temperature coefficient for precision circuits.
Ceramic capacitors (MLCC)Usually easy, with care.Value, voltage, dielectric (C0G, X7R, X5R), size. Note that capacitance under DC bias can differ between makers for the same nominal part.
Discrete semiconductors (diodes, small transistors, MOSFETs)Often possible.Pin-out (it can differ in the same package), voltage and current ratings, on-resistance, gate threshold, switching speed.
Voltage regulators, op-amps, logicSometimes pin-compatible parts exist.Pin-out, stability requirements (for example output capacitor type for LDOs), electrical specs, enable pin polarity.
Microcontrollers, FPGAs, RF and specialised ICsRarely; usually single source.Treat as single source. Plan stock early and consider a footprint that accepts a second package or family member.
Connectors and electromechanical partsVaries; mating parts must match.Pitch, mating part, height, pin numbering, current rating, mounting style.
  1. 1

    Identify your single-source lines

    Mark any line where only one MPN will work. These are the lines that need the most attention for stock and lifecycle.
  2. 2

    Add alternates where the design allows

    Add columns such as "Alternate 1 manufacturer / MPN" and "Alternate 2 manufacturer / MPN". Only list parts you have checked against the same footprint and circuit requirements.
  3. 3

    Say where any equivalent is fine

    For generic passives you can write "any equivalent meeting value, tolerance, voltage and size". This gives flexibility without losing control of the key parameters.
  4. 4

    Mark lines that must never be substituted

    Use a "No substitute" note for parts where even small differences matter: precision references, RF parts, safety-critical or certified components.

    Tip: A footprint that accepts two common package sizes, or two pin-compatible families, can make a future change much cheaper than a PCB re-spin.

Component lifecycle: active, NRND, EOL, PCN and last-time buys

Every component has a life. Manufacturers publish its status, and checking it before you finalise a design or a production order avoids building a product around a part that will soon disappear.

StatusWhat it typically meansWhat to do
ActiveIn normal production and recommended for new designs.Preferred for any new design.
NRND (not recommended for new designs)Still made, but the manufacturer signals it may be discontinued; supply may tighten.Avoid in new designs. For existing products, start looking for a replacement.
EOL announced / last-time buy (LTB)The manufacturer has announced discontinuation and a final date to place orders.Decide whether to buy enough stock for the remaining life of the product, or redesign. Note the LTB date.
Obsolete / discontinuedNo longer made. Only remaining distributor or broker stock exists.Redesign or choose an alternate. Remaining stock may be limited, expensive or hard to trace to the original maker.
PCN (product change notice)The manufacturer is changing something: process, site, material, marking or packaging.Read the notice. Most changes are minor, but some can affect form, fit or function, for example moisture sensitivity level or package dimensions.

Check before release

Check the lifecycle status of each MPN at the end of the design, not just at the start. Status can change during a long project.

Plan for long-life products

For products that will be built for many years, prefer parts from families with several makers and a long history, and review the BOM at least once a year.

Be careful with broker stock

Obsolete parts sold outside authorised channels carry a higher risk of counterfeit or poorly stored parts. Moisture-sensitive parts must have been stored and handled correctly (see J-STD-020 and J-STD-033).

Choosing parts that are easy to source

Design decisions made early, often for convenience, decide how easy the BOM is to buy later. These rules of thumb are general guidance for most commercial designs.

AreaEasy to source (typically)Harder to source (typically)
Passive sizes0402, 0603 and 0805 chip resistors and capacitorsVery large or very small sizes, unusual aspect ratios
Resistor valuesStandard E24 values (and E96 for 1% parts)Non-standard values or very tight tolerances where not needed
Capacitor dielectricsX7R, X5R and C0G in common voltage and value rangesHigh capacitance at high voltage in small sizes; special dielectrics
IC packagesSOIC, SOT-23, TSSOP, QFN in widely used sizesUnusual or very fine-pitch packages offered by one maker only
ConnectorsCommon pitches with several makers producing mating partsCustom or proprietary connectors from one source
ConsolidationReusing the same value and size across the designMany slightly different values that could be one value

Consolidate your passives

If a design uses 4.7k, 5.1k and 4.99k pull-ups where any one would work, choosing one value reduces the number of unique lines, the setup work and often the price. Fewer unique MPNs usually means a simpler, faster build.

How quantity and price breaks change the unit price of components

Components are usually sold with price breaks: the more you buy, the lower the unit price. Some parts also have a minimum order quantity (MOQ) or are sold only in full reels or trays.

EffectWhat happensHow it shows in a quote
Price breaksThe unit price falls at certain quantities, for example 10, 100, 1,000 pieces.Ordering a slightly larger quantity can sometimes cost about the same in total as a smaller one.
Minimum order quantity (MOQ)Some parts can only be bought above a certain quantity or in full packaging units.For a small build, the component line may cost more than the parts actually placed.
Attrition / sparesSmall passives can be lost during machine set-up and placement.A few extra pieces are typically allowed for small parts on reels; expensive parts are counted more carefully.
Exchange ratesMany parts are priced in foreign currency.Component prices can change between quotes when rates move.

Compare a few quantities

When you request an assembly quote, it can be worth comparing two or three board quantities. The component share of the price often falls noticeably as quantity grows, because more lines reach a better price break. See PCB cost factors for the board side of the price.

How Microplacer quotes components from your BOM

Here is how the component part of an assembly order works at Microplacer.

  1. 1

    Upload your files

    Upload Gerbers, BOM and pick-and-place. The assembly price is calculated instantly from the solder pads on your board; parts in BGA, LGA or 0201 packages go to engineering review. PCB assembly is done only in panels. See the assembly quote FAQ and panel guide.
  2. 2

    Components are quoted from your BOM

    We price each line using the MPNs in your BOM, from our electronic components store with millions of parts.
  3. 3

    Engineers check your files

    Before production our engineers check your files. Production notes in your files are read and compared with the options we offer.
  4. 4

    Write your substitution rules in the BOM

    Approved alternates, "any equivalent" lines and "No substitute" lines are production notes too. Putting them in the BOM up front means your intent is on file when components are quoted and when our engineers check your files.
  5. 5

    Pay and build

    Payment is made at order time, by online payment or bank transfer. In the instant assembly price, 5 to 50 boards are stencil-free and 55 boards or more use a shared stencil.

What to send us / what to specify when ordering

Files

BOM (spreadsheet), pick-and-place (centroid) file and Gerbers, all exported from the same design revision. An assembly drawing helps for polarity and unusual parts.

On every BOM line

Reference designators, quantity per board, manufacturer, full MPN, package, and a short description with key values.

Alternates and restrictions

Approved alternate MPNs, lines where any equivalent is fine (with key parameters), and lines marked "No substitute".

Not fitted and supplied parts

DNP lines, parts you will fit yourself, parts you will supply, and any mechanical items you want included.

Checklist before you upload

CheckDone when
Same revisionBOM, pick-and-place and Gerbers come from the same design export.
Exact MPNsEvery placed line has a full manufacturer part number, not just a description.
Package matches footprintThe package of each MPN matches the land pattern on the board.
Quantities match designatorsQuantity per board equals the number of reference designators on each line.
DNP markedUnfitted parts are marked DNP consistently in BOM and pick-and-place.
Alternates listedApproved alternates are given where the design allows; single-source and "No substitute" lines are marked.
Lifecycle checkedNo NRND, EOL or obsolete parts without a plan; recent PCNs reviewed.
Moisture-sensitive and ESD partsNoted where relevant so they can be handled per J-STD-033 and ANSI/ESD S20.20 practice.

Need parts or sourcing help?

Browse our electronic components page, read how component sourcing works, or see global component sourcing for parts that are hard to find.

Frequently asked questions

It is strongly recommended. If you do not mind which maker is used, you can say "any equivalent" on that line, but still give value, tolerance, voltage or power, and size so the right part is quoted.

Write it in the BOM: list approved alternate MPNs, mark lines where any equivalent is acceptable (with key parameters), and mark lines that must never be substituted. Our engineers check your files before production and read the production notes in them against the options we offer.

Not recommended for new designs. The part is still made, but the manufacturer suggests it may be discontinued. Avoid it in new designs and plan a replacement for existing ones.

Mark them as DNP (do not place) with quantity 0, and make sure the pick-and-place file treats them the same way. Alternatively remove them from both files.

Component prices depend on quantity, price breaks, stock and exchange rates, which can change over time. Comparing quotes at the same quantity and date gives the fairest comparison.

Boards with BGA, LGA or 0201 parts do not get an instant price; they go to engineering review and our team comes back to you with a quote. See PCB assembly capabilities.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us