+91 8866188126 [email protected]

EMS · Conformal coating

Conformal coating — a thin shield for your assembled boards

Conformal coating is a thin protective film applied over an assembled PCB. It helps the board cope with humidity, dust and contamination. Here is how it works, which options exist and what we need from you to quote it.

Get an instant quote

See how it works

Cleaned · dry · ready to coat
1/5 · Clean assembled board

Coating is applied after assembly, once the board is cleaned and dry.

How conformal coating works: Clean assembled board — Coating is applied after assembly, once the board is cleaned and dry. Mask keep-out areas — Connectors, headers and test points are masked so they stay uncoated. Apply the coating — A thin protective film is applied — sprayed here; dip, brush and selective coating are also used. Cure, de-mask & UV check — After curing the masks come off. Many coatings contain a UV tracer, so gaps and thin spots show up under UV light. Protected board — The film helps guard the board against moisture, dust and contamination — it is not waterproofing.

What is conformal coating — and who needs it?

The coating “conforms” to the shape of the board: it flows around the components and solder joints and cures into a thin, mostly transparent layer. It is not a box or an enclosure — it protects the surface of the board itself.

Moisture and condensation

Boards used outdoors, in humid climates or where temperature changes cause condensation benefit from a barrier against moisture.

Dust and contamination

Dust, fibres and conductive particles can settle between fine-pitch pins. A coating keeps them off the copper and solder.

Chemicals and handling

Some coatings resist oils, fuels or cleaning agents better than a bare board, depending on the material chosen.

Industrial and outdoor products

Controllers, power supplies, sensors, lighting drivers and field-installed equipment are common candidates.

Automotive and mobility

Products near engines, batteries or road spray often call for a coating as part of the customer’s specification.

When it is specified by your customer

Many buyers state a coating requirement in their drawing or purchase order. We work from that specification.

The coating process, step by step

A typical coating job follows the steps below. Coating comes after assembly, so it is planned together with your PCBA order and adds some time to it.

  1. 1

    Assembly and cleaning

    The boards are assembled first. Coating sticks well only to a clean surface, so flux residues and contamination are dealt with before coating, and the boards are dried.
  2. 2

    Masking the keep-out areas

    Connectors, headers, test points, switches, potentiometers, mounting holes and anything that must make electrical or mechanical contact is covered with masking tape, boots or a peelable mask, following your coating drawing.

    Tip: If a part must stay uncoated, it must be on the drawing. “Obvious” areas are not always obvious on a crowded board.

  3. 3

    Applying the coating

    The coating material is applied by spraying, selective (programmed) coating, dipping or brushing — the method depends on the material, the board and the quantity. Both sides can be coated if required.
  4. 4

    Curing

    The film is cured or dried as the material requires — for example in air, with heat, or with UV light for UV-cure materials. Boards are not handled until the film is ready.
  5. 5

    De-masking and inspection

    Masks are removed and the boards are inspected. Many coatings contain a UV tracer, so under UV light the coated areas glow and any bubbles, gaps, thin areas or coating inside keep-out areas become easy to spot.
  6. 6

    Touch-up, packing and dispatch

    Small defects are touched up where allowed by the specification, then the boards are packed and shipped with the rest of your order.

Coating materials and methods

There is no single “best” coating. The right choice depends on the environment, the operating temperature and whether the board will need repair later. If you are not sure, tell us where the product will be used and we will discuss options.

Coating typeTypical characterThings to keep in mind
Acrylic (AR)General-purpose, widely used, easy to apply.Usually the easiest to remove for rework; moderate chemical resistance.
Silicone (SR)Flexible, suits wide temperature swings.Rework is possible but usually slower than with acrylic; silicone residue can stop adhesives, labels or other coatings from sticking nearby.
Polyurethane / urethane (UR)Good chemical and abrasion resistance.Removal for rework takes more effort than acrylic.
Epoxy (ER)Hard, tough film.Very difficult to remove; rework is limited.
Parylene (XY)Very thin, very uniform film applied in a vacuum process.Specialised process; discuss with us early.

Spray

Good for many board types. Masking is used to protect keep-out areas.

Selective coating

A programmed nozzle coats only the defined areas, which can reduce masking on repeat production.

Dip

The board is dipped in the material for full coverage; heavy masking is needed for connectors.

Brush

Practical for small quantities, local protection or touch-up.

Coating vs potting

A coating is a thin film. Potting or encapsulation fills an enclosure or area with a thick compound — more protection, but much heavier and almost impossible to rework. If you need potting, mention it in your enquiry and we will review it.

What to send us

Conformal coating is quoted by our team after reviewing your requirement — it is not part of the instant online price.

InformationWhy it matters
Gerber, BOM and pick-and-place filesWe need the full assembly data to plan coating together with the PCBA. See preparing your files.
Coating drawing / masking guideShows which areas to coat and which to keep clear (connectors, test points, switches, holes). A marked-up PDF or assembly drawing is fine.
Coating material or specificationA material type (acrylic, silicone, urethane …) or the specification your customer requires.
Sides to coatTop, bottom or both.
Thickness and cure requirementsIf your specification states a film thickness range or cure method, include it.
Quantity and use environmentHelps us suggest a practical method and give an accurate quote.
  1. 1

    Get your PCB + assembly price online

    Use the instant quote for the bare boards and assembly, and save the quotation.
  2. 2

    Tell us about the coating

    Send the coating drawing and material details through Contact us or with “Send for quote”, mentioning your quote number.
  3. 3

    We review and quote

    Our engineers check the drawing, ask about anything unclear and send you the coating quotation.

What a good coating job includes

Drawing-based masking

Keep-out areas should come from your drawing, not be guessed. Anything unclear on the drawing is confirmed with you before production.

Visual and UV inspection

Coated boards are typically checked for coverage, bubbles, de-wetting and coating inside keep-out areas — under UV light when the material contains a UV tracer.

Standards as reference

Coating materials are commonly qualified to IPC-CC-830, and workmanship is often judged against IPC-A-610. See certifications & standards.

Coating and rework

Once a board is coated, repairing it means removing the coating locally first, then re-coating the area. Please finish testing and programming changes before coating wherever possible.

Frequently asked questions

No. The instant price covers the bare PCB and the assembly. Coating is quoted separately by our team after we see your coating drawing and material requirements.

No. A conformal coating improves resistance to humidity, condensation and contamination, but it is not designed for immersion. If your product will be submerged or sprayed directly, the enclosure and sealing design matter just as much.

It depends on where the product will be used and whether you expect rework. Acrylic is a common general-purpose choice; silicone suits wide temperature ranges; urethane and epoxy offer tougher films but are harder to rework. Tell us the use environment and any customer specification, and we will discuss options.

We will ask for one. Without it we cannot know which connectors, test points or contacts must stay clean, and coating them by mistake can make the board unusable.

Partial (selective) coating is common. Mark the areas to coat, or to keep clear, on your drawing and we will confirm what is practical in the quotation.

Yes. Masking, coating, curing and inspection happen after assembly, so they add time to the order. We confirm the timeline with your coating quotation.

Tell us about your boards and requirement through Contact us; we will review it and reply.

Related questions

Learn more — answers to the questions people ask next.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us