+91 8866188126 [email protected]

Design for assembly

Designing boards for assembly: BGA, fine-pitch and stencil basics

A few layout habits make the difference between boards that sail through assembly and boards that wait on questions. This guide covers panels, fiducials, polarity marks, part spacing, BGA and fine-pitch pads, solder paste and stencils, and a sourcing-friendly BOM.

Get an instant quote

Why design for assembly matters

Design for assembly (DFA) simply means drawing the board so that machines and people can build it right the first time.

Fewer defects

Clear marks, sensible spacing and correct pads reduce solder bridges, tombstoned parts and parts fitted the wrong way round.

Faster engineering check

Our engineers check every order before production. When the Gerber, BOM and pick-and-place file agree, there is nothing to ask you and your order keeps moving.

A clearer price

The online assembly price is based on the number of solder pads per board and the number of boards. Pads are counted from your Gerber paste layers, so removing paste openings for unused footprints keeps the count accurate. The full rules are in the assembly quote FAQ.

Panels for assembly

Pick-and-place machines and reflow ovens move boards on a conveyor, so small single boards have to be joined into a panel.

We assemble in panels only

Every PCBA order — prototype or production — is built in a panel. In the calculator choose Panel by Microplacer and we lay it out for you, or choose Panel by customer if your Gerber already contains the panel. Panel options, V-cut vs tab routing and spacing are explained in the panel guide.
Panel featureWhat it doesGeneral guidance
Edge railsA strip of plain board along the panel edges that the conveyor grips.Rails of around 5 mm on two or all four sides are a common choice. Keep parts off the rails.
FiducialsSmall copper dots the machine camera uses to find the exact position and angle of the panel.Usually three, placed asymmetrically on the rails so the panel cannot be loaded the wrong way round.
Tooling holesPlain, non-plated holes that let fixtures hold the panel steady.Typically placed in the rail corners, clear of copper and parts.
Separation (V-cut or tabs)How the boards are broken apart after assembly.Keep sensitive parts away from the break line — see the spacing section below.

Fiducials, polarity and designators

Machines align with fiducials; people check polarity and designators. Both need clean, readable marks.

Board fiducials

Besides the panel fiducials, a common practice is two or three fiducials on the board itself, and a local pair near large fine-pitch parts. A fiducial is usually a round bare copper pad with a clear (no solder mask, no silkscreen) area around it.

Pin 1 marks

Put a dot or notch next to pin 1 of every IC and connector, outside the part body so it is still visible after placement. Make sure the mark agrees with the footprint pin numbering.

Diode and capacitor polarity

Mark the cathode of diodes and LEDs and the + side of electrolytic and tantalum capacitors. Use the same convention across the whole board.

Designators that match everywhere

R1 on the silkscreen, R1 in the BOM and R1 in the pick-and-place file must be the same part. Mismatches are the most common reason an assembly order is put on hold. See preparing your files.

Component spacing and orientation

TopicWhy it mattersRule of thumb
Distance from board edgeParts near the edge can be damaged by handling or by the conveyor and depanelling.Keep SMD parts a few millimetres from the board outline; give tall or fragile parts more room.
V-cut and tab linesBreaking a panel bends the board along the cut, which can crack ceramic capacitors and solder joints.Keep ceramic capacitors and large parts well back from V-cut lines, and orient them parallel to the cut rather than across it.
Space between partsNozzles, inspection and rework all need room around each part.Leave extra clearance around tall parts, connectors and BGAs so neighbours can still be inspected and reworked.
OrientationConsistent rotation makes inspection quicker and reduces polarity mistakes.Where possible, align similar parts in the same direction (all 0° or all 90°).
Heavy and tall partsIn two-sided assembly the side built first hangs upside down during the second reflow, so heavy parts there can drop or shift.Put heavy, tall and through-hole parts on one side (usually the top, built last).

One side or both sides?

Assembling one side is simpler: one paste print, one placement run and one reflow. Two-sided assembly repeats those steps for the second side. If your board fits, putting all SMD parts on the top side usually saves cost and time.

Small passives on the bottom

If you need both sides, a common approach is to keep the bottom side to small, light passives and simple ICs, and put everything heavy on the top.

BGA and fine-pitch layout

BGA (ball grid array) and fine-pitch parts have many small pads close together. They reward careful layout.

  1. 1

    Start from the manufacturer’s recommended land pattern

    The part datasheet usually gives a recommended pad size and solder mask opening. For BGAs, pads are commonly the same size as or a little smaller than the ball diameter. Use the datasheet values rather than guessing.
  2. 2

    Choose solder-mask defined or non-solder-mask defined pads

    Most designs use non-solder-mask defined (NSMD) pads for BGAs, where the mask opening is larger than the copper pad. Follow the datasheet if it says otherwise, and keep the choice consistent for all pads of one part.
  3. 3

    Plan the fanout

    On coarser-pitch BGAs, the outer rows can be routed out on the surface and inner balls taken down with a short trace to a via between the pads (the “dog-bone” pattern). Finer pitches often need via-in-pad and more layers.
  4. 4

    Use filled vias for via-in-pad

    An open via inside a pad steals solder and can leave a void or a weak joint. If you place vias in pads, choose a filled and capped via covering in the calculator (epoxy or copper paste filled & capped). Plain tented vias are fine when the via sits outside the pad.

    Tip: Our online calculator offers via covering options from tented up to epoxy filled & capped and copper paste filled & capped.

  5. 5

    Pick a flat surface finish

    BGAs and fine-pitch parts need flat pads. ENIG gives a flat gold surface and is the usual choice; OSP is also flat but has a shorter shelf life. HASL is economical but less flat, so it suits coarser parts better.

BGA, LGA and 0201 parts go to engineering review

Boards with BGA or LGA parts (hidden joints under the package) or 0201 or smaller parts are not priced instantly. Send your files with “Send for quote” and our engineers review the design, then email you the PCB + PCBA quotation.

Solder paste and stencil basics

The stencil decides how much solder each SMD pad gets. Too little gives weak joints; too much gives bridges.

ItemWhat it isGeneral guidance
Paste layerThe top and bottom paste (cream) layers in your Gerber. The stencil openings are made from them.Always export paste layers. Without them the stencil and the pad count have to be estimated.
Aperture sizeThe size of each opening in the stencil.Often equal to or slightly smaller than the pad. Large thermal pads (for example under QFN parts) are usually split into a grid of smaller openings to avoid floating and voids.
Stencil thicknessSets how tall the paste deposit is.Thinner stencils suit fine-pitch and very small parts; thicker ones suit larger parts. One stencil thickness has to balance the smallest and largest parts on the board.
Through-hole onlyNo SMD paste is printed.Boards with only through-hole parts do not need a stencil.

5 to 50 boards: stencil free

For small batches there is no stencil charge.

55 boards and more: shared stencil

A one-time shared stencil (top and bottom) is added to your quote. Need your own stencil for in-house work? See our stencil solution.

Through-hole parts and thermal relief

Connectors, large capacitors and transformers are often through-hole. In the industry they are typically soldered after the SMD parts, by wave, selective soldering or by hand.

Hole size

A common rule of thumb is a finished hole roughly 0.2–0.3 mm larger than the lead diameter (or the diagonal of a square lead), so the lead goes in easily and solder can flow up the barrel.

Thermal relief on planes

Pins connected to large copper planes should use thermal relief spokes. A solid connection pulls heat away and makes the joint hard to solder properly.

Pad and spacing

Give through-hole pads a generous ring and keep SMD parts clear of the area around them, so the soldering iron or wave can reach without disturbing neighbours.

Components and a sourcing-friendly BOM

Components are not part of the assembly price. If we source them, we quote them separately from your BOM; if you supply all parts, the assembly price is complete.

  1. 1

    Give a full manufacturer part number for every line

    An exact MPN removes guesswork about value, tolerance, voltage and package.
  2. 2

    Add an alternative where you can

    For common passives and generic parts, noting an approved alternative helps when a part is out of stock or has a long lead time.
  3. 3

    Check the part is active

    Avoid parts marked end-of-life or not recommended for new designs; they are harder to buy and may need a substitute.
  4. 4

    Mark parts not to fit

    List DNP (do not place) parts clearly so they are neither bought nor placed.

More on how parts are bought and checked: component sourcing.

Quick questions

No — assembly is done in panels only. Choose “Panel by Microplacer” and we create the panel for you. See the panel guide.

Panel fiducials locate the panel, but small errors add up across a large panel. Board-level fiducials, plus a local pair near fine-pitch parts, give the machine a more accurate reference — a good habit whenever you have room.

Boards with BGA or LGA parts are not priced instantly; our engineers review the design first. Send your files with “Send for quote” and we email you the PCB + PCBA quotation.

ENIG is the usual choice because the pads are flat. OSP is also flat but has a shorter shelf life. HASL is economical and works well for coarser parts.

For 5 to 50 boards there is no stencil charge. From 55 boards a one-time shared stencil is added to the quote. Through-hole-only boards need no stencil.

No. If we source parts, they are quoted separately from your BOM. Details are in the assembly quote FAQ.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us