+91 8866188126 [email protected]

PCB assembly guide

Solder paste, stencils and reflow profiles explained

Every surface-mount joint on your board is made in three linked steps: paste is printed through a stencil, parts are placed into the wet paste, and the board passes through a reflow oven. This guide explains each step in plain words, with typical values used across the industry, so you know what affects joint quality and what to tell us when you order assembly.

Get an instant quote

How paste, stencil and reflow decide most solder-joint quality

Industry studies and day-to-day experience on SMT lines point the same way: a large share of soldering defects can be traced back to the paste print, not to placement or the oven. The three steps work as one system, so a problem in one step often shows up as a defect in another.

Paste sets the material

The alloy decides the melting point and joint strength; the powder size decides how small an opening the paste can print through; the flux decides how well the solder wets and what residue is left.

Stencil sets the volume

Stencil thickness multiplied by aperture area is roughly the paste volume on each pad. Too little gives weak or open joints; too much gives bridges and solder balls.

Reflow sets the joint

The temperature profile activates the flux, melts the solder and lets it wet the pad and lead, then cools it into a sound joint without overheating parts or the board.

What this means for you

Most of these choices are made by the assembler, but your design decides the starting point: pad sizes, package types, surface finish and any special notes. Good footprints and a flat finish make the paste print easier and the result more consistent. See design for assembly for layout rules.

Solder paste: alloy, powder size, shelf life and working time

Solder paste is a mix of tiny solder spheres (typically close to 90% of the weight) suspended in a flux medium. Its main properties are described in industry standards such as J-STD-005 (paste), J-STD-006 (alloys) and J-STD-004 (flux).

Alloy (common names)Melting behaviourTypical use
SAC305 (Sn96.5 Ag3.0 Cu0.5)Melts over roughly 217–220 °CThe most common lead-free (RoHS) alloy for general SMT assembly
Low-silver SAC alloys (e.g. SAC0307)Melts slightly higher and over a wider rangeCost-sensitive lead-free products; wetting can be a little slower
Sn63 Pb37 (eutectic tin-lead)Melts sharply at about 183 °CLeaded assembly where RoHS does not apply, such as some repair and exempt equipment
Low-temperature SnBi alloysMelt at about 138 °CHeat-sensitive parts or boards; joints are more brittle, so used selectively
Powder typeTypical particle sizeWhere it is used
Type 3About 25–45 µmGeneral SMT with 0603 and larger passives and pitches of about 0.5 mm and above
Type 4About 20–38 µmFine-pitch ICs, 0402 passives, QFN and most modern mixed boards
Type 5About 15–25 µmVery small apertures such as 0201 parts and fine-pitch BGA or LGA pads

A common rule for powder size

Aim for at least four to five of the largest particles across the smallest aperture width. If fewer fit, the paste tends to clog the opening and print unevenly, so a finer powder type is chosen.

Storage and shelf life

Paste is usually kept refrigerated (often around 0–10 °C) and has a shelf life of several months from manufacture, as stated on its datasheet. It is warmed to room temperature in the sealed jar before opening, typically for a few hours, so moisture does not condense into it.

Life on the stencil

Once open, paste slowly dries and picks up moisture. Datasheets usually state how many hours it can stay on the stencil and still print well; old paste on the stencil is replaced rather than topped up indefinitely.

Time from print to reflow

Printed boards are normally placed and reflowed within a few hours. Paste left too long loses tack (parts can shift) and flux activity, which can lead to poor wetting and solder balls.

Laser-cut stainless-steel stencils: thickness, apertures and step stencils

A stencil is a thin metal foil with one opening (aperture) for each pad that needs paste. Laser-cut stainless steel is the everyday choice; electroformed nickel foils are used where very fine features need extra-smooth aperture walls. General design guidance is published in IPC-7525.

Foil thickness (typical)Paste volumeUsually chosen for
0.08–0.10 mmLowBoards dominated by 0201/0402 parts, fine-pitch BGA or 0.4 mm pitch ICs
0.10–0.12 mmMediumThe most common range for mixed boards with 0402–1206 passives, SOIC, QFP and QFN
0.13–0.15 mmHigherBoards with mainly larger parts, power packages and connectors that need more solder

Area ratio

Aperture opening area divided by the area of its walls. A common rule is to keep it at about 0.66 or more, so paste releases cleanly from the stencil instead of staying in the hole.

Aspect ratio

Aperture width divided by foil thickness. A common rule is about 1.5 or more for long, narrow apertures. If a fine pad fails this check, a thinner foil or a larger opening is used.

Aperture reductions

Openings are often made slightly smaller than the pad (for example a 5–10% reduction) to reduce bridging, and home-plate or inverted-U shapes are used on small chip parts to limit solder balls.

Windowpane on thermal pads

Large exposed pads under QFN and power packages are usually printed through several smaller windows, covering roughly 50–80% of the pad, so the part does not float and voids are reduced.

Fiducials

Fiducial marks on the board and stencil let the printer and placement machine align automatically. Place them as described in our design for assembly guide.

Step stencils

When one board needs both very little paste (fine pitch) and a lot (connectors, shields), a stencil can be thinned or thickened in local areas. Step stencils add cost and need clearance around the step, so they are used only when apertures alone cannot balance the volumes.

Through-hole parts and paste

Pin-in-paste (printing paste over through-hole pads and reflowing the leads) needs carefully sized overprinted apertures and parts rated for reflow temperatures. If you want it, mention it in your production notes so our engineers can review it.

How Microplacer handles stencils

You do not need to order or design a stencil separately for your Microplacer PCBA order — it is part of the assembly quote.

Your orderHow the stencil is handled
5 to 50 boardsStencil free of charge
55 boards and moreShared stencil
BGA, LGA or 0201 parts on the boardThe order goes to engineering review before the price is confirmed, because these parts need closer checks of apertures and paste volume
Board formatAssembly is done in panels only — see the panel guide for how boards are grouped
  1. 1

    Upload your files and get an instant price

    The PCBA instant price is calculated from the number of solder pads on your board, so the paste print is already part of what you are quoted. Components are quoted separately from your BOM. See the assembly quote FAQ.
  2. 2

    Our engineers check the files

    Before production, our engineers check your files, including the paste layers, and read any production notes in them and compare those notes with the options we offer.
  3. 3

    Panelised assembly

    Boards are assembled in panels. Read the panel guide to understand how boards are grouped into a panel, which also sets the stencil layout.

Questions about stencils?

For more about stencils, see our stencil solutions page, or contact our team with your question.

Reflow profile zones and profiling with thermocouples

A reflow profile is the temperature the board itself sees over time as it moves through the oven. The values below are typical for SAC lead-free paste and are general guidance only — the paste datasheet and the most heat-sensitive part on the board always set the real limits.

ZoneWhat happensTypical lead-free values (general guidance)
Preheat (ramp)The board warms evenly and solvents start to evaporateAbout 1–3 °C per second up to roughly 150 °C
Soak (thermal equalisation)Large and small parts reach similar temperatures; flux activates and removes oxidesRoughly 150–200 °C for about 60–120 seconds
Reflow (time above liquidus)The solder melts, wets the pads and leads, and forms the jointPeak about 235–250 °C; about 45–90 seconds above 217 °C
CoolingThe joint solidifies into its final grain structureControlled cooling, commonly kept below about 6 °C per second

Ramp-soak-spike

The classic profile with a distinct soak plateau. Helpful on boards with large thermal differences, such as a big ground plane next to small parts.

Ramp-to-spike (linear)

A steady climb straight to peak without a long plateau. Often used on simpler boards and with pastes whose flux prefers less time at soak temperature.
  1. 1

    Attach thermocouples to a sample board

    Fine thermocouples are fixed with high-temperature solder, adhesive or tape at representative points: a large thermal mass part (BGA, power device, connector), the smallest passives, and an open board area.
  2. 2

    Run the board through the oven with a profiler

    A data logger travels with the board and records each point. The spread between the hottest and coldest points (delta-T) shows how evenly the board heats.
  3. 3

    Compare with the paste and part limits

    Each point is checked against the paste datasheet window and the peak rating of every part. A common goal is to keep delta-T small, often within about 10 °C at peak.
  4. 4

    Adjust zones and belt speed, then repeat

    Zone temperatures and conveyor speed are tuned until all points sit inside the window. The final profile is saved for that board and checked again when the design or paste changes.

    Tip: Heavy copper, thick boards and large metal parts need more heat. Mention them in your notes so they can be taken into account.

Lead-free (RoHS) vs leaded (SnPb) assembly

The alloy choice changes the oven temperatures, which parts are suitable and whether the finished product can be sold where RoHS applies.

TopicLead-free (SAC)Leaded (SnPb)
Melting pointAbout 217–220 °CAbout 183 °C
Typical peak on the boardAbout 235–250 °CAbout 205–225 °C
Part ratingsParts must be rated for lead-free reflow; J-STD-020 classifies package peak ratings, often up to about 245–260 °CParts rated for the lower SnPb peak are fine; lead-free parts can usually be reflowed at SnPb temperatures, but mixed-alloy BGA balls need care
Moisture sensitivityHigher peak means more risk for moisture-sensitive parts; follow MSL handling and baking per J-STD-033Same rules apply, with somewhat less thermal stress
Joint appearanceOften slightly grainy or matte — normal for lead-freeUsually bright and smooth
RoHSCompliantNot compliant; used where RoHS does not apply or an exemption is in place

Match the surface finish to the alloy

For a RoHS product, the board finish must be lead-free as well (for example Lead-free HASL, ENIG or OSP). Leaded HASL boards are not RoHS compliant even if the assembly uses lead-free paste. See our surface finish guide.

Flux chemistry: no-clean vs water-soluble

Flux cleans oxides from the metal surfaces during reflow and helps the solder wet. Paste fluxes are classified in J-STD-004 by base material and activity (for example ROL0 is a low-activity, halide-free rosin type).

Flux typeResidue after reflowCleaningThings to know
No-clean (rosin or resin based)Small amount of clear, benign residueNot required in most productsThe most common choice. Residue can interfere with some conformal coatings, high-impedance circuits and test-probe contact, so cleaning may still be specified.
Water-soluble (organic acid)Active residue that must be removedRequired, typically with water washing soon after reflowStrong wetting on hard-to-solder surfaces, but residue left on the board can cause corrosion and leakage over time.

Cleaning and conformal coating

Coatings bond best to a clean surface. If your board will be coated, tell us so the cleaning step and coating are planned together. See conformal coating.

Cleanliness checks

Ionic contamination and residue checks are commonly used to verify cleaning on high-reliability boards. Acceptance criteria for finished assemblies are described in IPC-A-610.

Common reflow defects and their usual causes

Most defects have several possible causes, and the fix usually starts with the paste print. The table lists the usual suspects as general guidance.

DefectWhat you seeUsual causesTypical fixes
Solder balls / beadsSmall solder spheres beside chip parts or across the maskExcess paste, paste under the part body, moisture in paste, too fast a preheat, printed boards left too longAperture reduction or home-plate shape, correct paste handling, gentler ramp
BridgingSolder joining two neighbouring pinsToo much paste, smeared print, stencil misalignment, too little solder mask between padsThinner foil or smaller apertures, stencil cleaning, mask dams between fine-pitch pads
TombstoningA small passive standing up on one endUnequal heating or paste volume on the two pads, unbalanced pad sizes or copper connectionsSymmetrical pads and thermal relief, balanced apertures, longer soak
Insufficient solder / opensThin, dull or missing jointsClogged apertures, too thin a foil, poor paste release, lifted leads (coplanarity)Check area ratio, finer powder, stencil wiping, part inspection
VoidsGas pockets inside joints, seen on X-rayOutgassing flux on large pads, via-in-pad without filling, profile too shortWindowpane apertures, filled or tented vias, profile adjustment
Head-in-pillowBGA ball rests on the paste but does not mergeBoard or package warpage, oxidised balls, flux exhausted before the solder meltsProfile tuning, fresh paste, part storage and MSL control

Design is part of the fix

Tombstoning, bridging and voids are often traced to footprints, not the oven. Using land patterns based on IPC-7351 and keeping vias out of small pads prevents many of these defects before the board is made.

What to tell us in your production notes

Our engineers read the production notes in your files and compare them with the options we offer. Clear notes help our team review your board correctly.

  1. 1

    Send complete, matching files

    Include Gerbers with the paste layers (top and bottom), a pick-and-place file and a BOM with manufacturer part numbers. See design files for the full list.
  2. 2

    State lead-free or leaded

    Say whether the product must be RoHS compliant. If you need leaded assembly for an exempt product, write it clearly so our team can confirm what is possible.
  3. 3

    Flag special parts

    List BGA, LGA, 0201, large thermal-pad parts, heat-sensitive parts (batteries, some connectors, displays, crystals) and any moisture-sensitive packages with their MSL rating.
  4. 4

    Mention cleaning and coating needs

    Note if the board must be cleaned, if no residue is allowed in certain areas, or if it will be conformal coated after assembly.
  5. 5

    Describe special paste requests

    Pin-in-paste for through-hole parts, extra solder on connectors or shields, or a requested paste type should all be written in the notes for engineering review.

Components for your BOM

Parts are quoted from your BOM. Browse our components store with millions of parts through electronic components.

Learn the full assembly flow

Paste printing is one stage of assembly. See how PCB assembly works and our stencil solutions.

Frequently asked questions

For 5 to 50 boards the stencil is free. From 55 boards a shared stencil is used. You do not need to order one separately.

No. Send the paste layers in your Gerbers. Our engineers check the files before production, and if you have special aperture requests you can add them to your production notes.

These parts need very small, precise paste deposits and closer checks of apertures, powder size and profile. Our team reviews such boards before the price is confirmed rather than relying on the instant price alone.

Flat finishes such as ENIG or OSP usually give the most even paste print on fine-pitch and BGA pads. See the surface finish guide.

For most products it is not. It can matter for boards that will be conformal coated, high-impedance or high-frequency circuits, and test points that need clean contact. Mention these in your notes.

Lead-free alloys often solidify with a matte, slightly grainy surface. This is normal and is not by itself a sign of a bad joint; inspection criteria in IPC-A-610 take this into account.

PCBA at Microplacer is done in panels only. The panel guide explains how panels are set up.

Related questions

Learn more — answers to the questions people ask next.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us